Replacing the Printhead Cleaning Roll Kit Components on the HP Latex R Printer | HP Latex | HP
Learn how to replace the Printhead Cleaning Roll Kit Components on the HP Latex R Printer Series.
Follow these steps to replace the Printhead Cleaning Roll Kit Components on the HP Latex R Printer Series:
- The printhead cleaning roll kit contains a new cleaning roll, printhead cleaning blade, aerosol filters, a left spittoon foam, a drop-detector spittoon foam, Distilled water
- From Internal Print Server, touch the Applications bar, then Other supplies and then touch Replace.
- Follow these steps to replace the left spittoon foam.
- Open the top cover, and then pull the curing module out of the printer.
- From the left side of the printer, remove the left spittoon foam.
- Bend the foam and slide it into the left spittoon slot, making sure it lays flat.
- From the IPS, touch Next to move to the next task.
- Follow these steps to replace the left printhead cleaning blade.
- Next to the left spittoon, grab the center of the left printhead cleaning blade, and then pull it out of the printer.
- Install the new left printhead cleaning blade into the printer.
- Close the curing module, and then close the top cover.
- From the IPS, follow these steps to refill the water tank.
- Open the water tank cap and slowly fill the tank with distilled water
- Touch Next to follow these steps to replace the aerosol filters.
- Open the carriage cover, pull up on the latch on the right side of the aerosol filter module.
- Open the filter lid, remove the frame and the filter from the frame.
- Use a screwdriver and then maintenance kit brush to clean the frame.
- Install the new filter into the frame, and then slide the frame into the aerosol container, close the filter lid, and then close the latch.
- Repeat this process for the other aerosol filter.
- With both filters replaced, close the carriage cover.
- Follow these steps to empty the printhead cleaning waste bottle.
- Open the printhead cleaning roll door.
- Remove the waste bottle from the printer, and then empty it.
- Place the empty waste bottle back in its original location.
- Follow these steps to replace the drop-detector spittoon foam.
- Open the carriage cover. manually move the carriage to the left.
- Slide the drop-detector spittoon foam out of the printer.
- Slide the new drop-detector foam into the its slot, making sure it lays flat.
- Follow these steps to replace the printhead cleaning roll.
- With the carriage cover still open, open the printhead cleaning roll door.
- From the IPS, touch Next to wind the printhead cleaning roll material.
- Pull the upper-left black knob, and then move the pinch system aside.
- Remove the end of the roll and use it to thoroughly clean and remove all ink waste from the printer.
- Use the end of the roll to clean the orange printhead cleaning blade,
- the transparent printhead cleaning blade,
- the entire surface of the middle diverter,
- the left diverter, and the left latch.
- Wipe any ink and fiber particles from each piece after cleaning.
- Use a putty knife and screwdriver to scrape the dried ink from sloping surfaces and to remove waste from the drilling hole respectively.
- Clean the fluid dispenser nozzle to make sure it’s not clogged.
- Turn the feed roller until you reach the end of the roll.
- Turn the take-up roller until the material is completely out of the assembly.
- Slide both rolls off their axles.
- Follow the instructions provided with the new roll and dispose of the roll with the used cleaning material.
- Remove the empty core and keep it to use as a take-up core.
- Slide the take-up core onto the lower axle.
- Slide the end cap on to the roll until it clicks into place.
- The empty core must be aligned against the end cap.
- Slide the new roll onto the upper axle.
- Slide the end cap on the upper axle, and then slide the cap and axle together.
- You will hear a click when correctly installed.
- Slide the leading edge of the roll over the upper rollers, but below the central diverter.
- Thread the leading edge of the cleaning material through the rollers on the left.
- Do not thread the leading edge behind the roller on the left. This roller must stay between the roll and the material.
- Thread the leading edge down the left side of the assembly.
- Install the leading-edge tabs into the slots in the take-up core.
- Turn the take-up core several times to attach the roll to the core.
- Move the black knob to the original position to restore the pinch system.
- Close the printhead cleaning roll door, and then close the carriage cover.
- From the IPS, touch Close,a progress bar indicates the stages of completion of all replacement tasks.
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Replacing the Printhead Cleaning Roll Kit Components on the HP Latex R Printer | HP Latex | HP
https://www.youtube.com/user/HP
No comments:
Post a Comment