Installing HP Jetdirect 3000w NFC/Wireless & 3100w BLE/NFC/Wireless Accessory | HP Jetdirect | HP
Learn how to install an HP Jetdirect 3000w NFC/Wireless and 3100w BLE/NFC/Wireless accessory. For more information to setup, install, and configure the HP Jetdirect 3000w NFC/Wireless Accessory, visit our support site https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to install an HP Jetdirect 3000w NFC/Wireless and 3100w BLE/NFC/Wireless accessory:
- Before you get started, you’ll need to update the printer with the latest firmware.
- First, make sure the accessory is not connected to the printer.
- Then, go to the FutureSmart page on the HP website, and click Upgrade now.
- Find your printer in the list of results, then click the corresponding Firmware download link.
- Follow the on-screen instructions for updating your printer’s firmware.
- Now you’re ready to install your new HP Jetdirect wireless accessory.
- Open the box and make sure it contains the accessory, USB cables, and fastener strips.
- Depending on your printer model, you can install the accessory in the printer’s Hardware Integration Pocket, or HIP, or on the outside of the printer.
- To install the accessory in the HIP,
- First, press the power button on the front of the printer to turn it off, and then disconnect the power cord.
- Using a flathead screwdriver, gently pry off the HIP cover.
- Next, connect the white connector on the short USB cable to the accessory.
- Connect the other end of the short USB cable to the USB port in the HIP.
- Insert the clips on the accessory into the slots, and then gently snap the accessory into place so that it is securely attached.
- Finally, connect the power cord, and turn on the printer.
- To install the accessory on the outside of the printer,
- First, press the power button on the front of the printer to turn it off, and then disconnect the power cord from the printer.
- Next, connect the white connector on the long USB cable to the accessory.
- Push the cable into the slot on the accessory cover.
- Then insert the clips on the accessory into the accessory cover.
- Press down firmly to fully attach the cover.
- Attach one of the fastener strips to the bottom of the accessory.
- Remove the backing paper to attach the other strip to the top of the printer.
- Position the accessory on the fastener strip to attach it to the top of the printer.
- Connect the other end of the long USB cable to the USB accessory port, located on the back of the printer.
- Finally, connect the power cord, and turn on the printer.
#HP #HPSupport #HPJetdirect
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Installing HP Jetdirect 3000w NFC/Wireless & 3100w BLE/NFC/Wireless Accessory | HP Jetdirect | HP
https://www.youtube.com/user/HP
No comments:
Post a Comment