Learn how to refill the ink tanks on the HP DeskJet GT 5810 and 5820 printers. To know more about refilling the ink tanks on the HP DeskJet GT 5810 and 5820 printers on our support site: http://support.hp.com/us-en/document/...
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to refill the ink tanks on the HP DeskJet GT 5810 and 5820 printers:
- First, open the ink tank lid.
- Remove the plug from the ink tank you are refilling.
- Place the plug upright to avoid getting ink on any other surface.
- Remove the cap from the ink bottle.
- Slowly pull the seal tab off and place directly in the trash or on a protective material to avoid getting ink on any other surface.
- Twist the cap firmly back onto the bottle.
- Flip open the cap lid.
- With the ink bottle upside down, place the top of the ink bottle on the tank spout.
- Do not squeeze the ink bottle or overfill the ink tank.
- Gently push down.
- Ink drains from the bottle into the ink tank.
- If the bottle does not start draining ink, remove the bottle, then push the bottle onto the ink spout again.
- Fill ink up to the maximum fill marker.
- To prevent leaks, do not exceed the maximum fill marker.
- Close the ink bottle lid and set the bottle aside.
- Push the ink tank plug back into its slot to seal the tank.
- Make sure the plug is pressed firmly into place.
- Repeat these steps to refill any other low or empty tanks.
- Close the ink tank lid.
- Your printer is full of ink and ready to print.
#HP #HPSupport #HPDeskJet
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Refilling the Ink Tanks on the HP DeskJet GT 5810 and 5820 Printers | HP DeskJet | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, deskjet 5810, deskjet 5820, refill, ink tanks, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, h...Refilling the Ink Tanks on the HP DeskJet GT 5810 and 5820 Printers | HP DeskJet | HP
Learn how to print in quiet mode on HP Printers. For more information about printing in quiet mode, visit our support site: https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to print in quiet mode on HP Printers:
- On your printer control panel, navigate to and touch Setup.
- Touch Preferences.
- Touch Quiet Mode, and then enable the option.
- Touch OK to start noise-sensitive printing.
- To run Quiet Mode only at specified times, turn on Schedule.
- To change the scheduled time, touch Time, and then touch Yes.
- Set the start time, and then touch Next.
- Set the end time, and then touch OK.
- Quiet Mode runs on the new schedule.
- When printing from your computer or mobile device, open the Printer Properties or Printing Preferences, and select printing on plain paper with normal print quality.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Print in Quiet Mode on HP Printers | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, How To Print in Quiet Mode on HP Pr...How To Print in Quiet Mode on HP Printers | HP Printers | HP
Learn how to replace the printheads on the HP DeskJet GT 5810 and 5820 printers. Replace printheads that are damaged or no longer functioning properly.
Learn more about replacing printheads on HP DeskJet GT 5810 and 5820 printers on our support site: http://support.hp.com/us-en/document/...
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace the printheads on the HP DeskJet GT 5810 and 5820 printers:
- If one printhead needs to be replaced, you must replace both printheads at the same time, or an error will occur.
- First, power on the printer.
- Extend the input tray.
- Load plain white paper into the input tray.
- Adjust the paper width guide so it touches the edge of the paper.
- Check the ink tanks to make sure all of the ink levels are above the minimum fill line.
- Close the output tray extender, then rotate the output tray to the left to close it.
- Make sure the ink valve is unlocked.
- Open the exterior door,
- Open the printhead access door.
- Manually move the carriage to the access area in the center of the printer.
- Push down on the blue carriage latch to open the lid.
- Press down on the tri-color printhead to release it, then pull the printhead out of the slot.
- Hold the printhead upright to avoid getting ink on other surfaces, and do not touch the printhead towers because they could contain residual ink.
- Next, press down on the black printhead to release it, then pull the printhead out of the slot.
- Open the package and remove the tri-color printhead.
- Pull the orange plug straight up from the top.
- Pull the protective tape using the orange pull tab.
- Do not touch the copper colored contacts or ink nozzles. Touching the contacts or nozzles can result in clogs, ink failure, and bad electrical connections.
- Slide the printhead at an upward angle into the left slot,
- Then push on it until it snaps into place.
- Open the package and remove the black printhead.
- Pull the orange plug straight up from the top.
- Pull the protective tape using the orange pull tab.
- Slide the printhead at an upward angle into the right slot,
- Then push on it until it snaps into place.
- Both printheads must be replaced at the same time to avoid printing issues.
- Close the blue carriage latch by pushing it down until it snaps into place.
- The carriage latch must be closed to prevent damage to the printer.
- Do not open the blue carriage latch after the printheads are installed.
- Opening the latch might result in ink system errors.
- Close the printhead access door.
- Close the exterior door.
- Pull out the output tray, then raise the tray extender.
- After the printheads are installed, you must align the printheads and prime the ink system.
- Do not disconnect the power cord or move the printer during the priming process.
- When you see the blinking P on the printer’s control panel, press the Resume button for three seconds.
- The alignment starts when a blinking A appears on the control panel.
- An alignment page prints.
- Lift the scanner lid, then place the alignment page, print side down, on the right front corner of the scanner glass.
- Close the scanner lid.
- On the control panel, press the Start Color Copy button.
- The page scans and the printer aligns the printheads.
- After the printheads are aligned, the printer starts the ink priming process.
- This process can take up to 45 minutes.
#HP #HPSupport #HPDeskJet
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Replacing the Printheads on the HP DeskJet GT 5810 and 5820 Printers | HP DeskJet | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, deskjet gt 5810, deskjet gt 5820, printhead, replace, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, sup...Replacing the Printheads on the HP DeskJet GT 5810 and 5820 Printers | HP DeskJet | HP
Learn how to use the HP Accessibility Assistant Voice Commands. Perform copy jobs, change accessibility settings, and use pre-defined Auto Quicksets using Voice Command with the HP Accessibility Assistant.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to use the HP Accessibility Assistant Voice Commands:
- The HP Accessibility Assistant requires the printer language set to English, and all Voice Commands must be spoken in English.
- Copy documents or photos using the Voice Command button on your HP LaserJet MFP with the HP Accessibility Assistant installed.
- Load the document to copy face-up in the ADF, or face-down on the scanner glass.
- Use the guides on the scanner glass to place the document in the correct location.
- On the HP Accessibility Assistant, press the Voice Command button, and wait for the ding sound.
- Say the copy function you want to perform, including any copy settings in the same command.
- The HP Accessibility Assistant repeats the request back to you, and then asks you to confirm the request is correct.
- Wait for the ding sound, and then respond.
- If the information is correct, say “Yes†or “Correctâ€.
- The HP Accessibility Assistant says, “Preparing Job.â€
- If the information repeated back to you is not correct, you can edit or cancel the original command.
- Press the Voice Command button, and wait for the ding sound.
- Say the copy function you want to perform.
- The HP Accessibility Assistant repeats the request back to you, and then asks you to confirm the request is correct.
- Wait for the ding sound, and then respond.
- To edit the original command, say “Noâ€, followed by the voice command you want to use.
- The HP Accessibility Assistant repeats the request back to you, and then asks you to confirm the request is correct.
- Wait for the ding sound, and then respond.
- To cancel the command, say “Cancelâ€.
- Change Accessibility settings using the Voice Command button on your HP LaserJet MFP with the HP Accessibility Assistant installed.
- Press the Voice Command button, and wait for the ding sound.
- Say the name of the setting you want to change, followed by the command.
- The HP Accessibility Assistant repeats the request back to you.
- After the ding sound, the settings are adjusted according to your command.
- Keep in mind, adjusting settings does not change the default settings.
- Default settings restore at the end of each user session.
- To set additional options, press the Voice Command button again, and wait for the ding sound.
- Use the Voice Command button to activate pre-defined Auto Quicksets on your HP LaserJet MFP with the HP Accessibility Assistant installed.
- Load the document to copy face-up in the ADF, or face-down on the scanner glass.
- Use the guides on the scanner glass to place the document in the correct location.
- To initiate a saved Auto Quickset, press the Voice Command button, and wait for the ding sound.
- Say “Auto Quicksetâ€, followed by the Auto Quickset number.
- The HP Accessibility Assistant repeats the request back to you, including the Auto Quickset description, if defined.
- After the ding sound, the printer pulls the original document into the printer and completes the Auto Quickset request.
- For more information on using the HP Accessibility Assistant, refer to the HP Accessibility Assistant User Guide or go to hp.com/support/HPAA.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
HP Accessibility Assistant Voice Commands | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, HP Accessibility Assistant, HPAA, V...HP Accessibility Assistant Voice Commands | HP Printers | HP
Learn how to use the HP Accessibility Assistant buttons to navigate the control panel and perform different printer functions.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to use the HP Accessibility Assistant buttons:
- Press the Screen Reader button to activate a screen reader who narrates control panel information –
- “Screen reader on. Start Quick Copy.â€
- Press the Screen Reader button again to turn off the screen reader.
- “Screen reader off.â€
- Press the Quick Access Accessibility button to launch a shortcut to the printer Accessibility menu, where you can access features including High Contrast and Screen Zoom.
- Keep in mind, adjusting settings does not change the default settings.
- Default settings restore at the end of each user session.
- Press the Previous or Left arrow button to move the current focus to the previous item.
- Hold the button for two or more seconds to move the focus to the first element on the screen.
- Press the Circle button in the center of the HP Accessibility Assistant to select an option, or choose OK.
- Press the Next or Right arrow button to move the current focus to the next item.
- Hold the button for two or more seconds to move the focus to the last element on the screen.
- Use the Back button to close the on-screen keyboard.
- Collapse open panels on the right side of the control panel,
- return to an application home page, or return the focus to the default control.
- Press the Home button at any time to return to the top application menu or to the main Home screen.
- When Copy, Start, or Send display on the control panel, pressing the Start button activates the function.
- Pressing Start on the main screen activates Quick Copy Start.
- Use voice commands to perform copy jobs, change accessibility settings, and use predefined Auto Quicksets.
- With the original document loaded in the automatic document feeder or scanner glass, press the Voice Command button.
- Say the copy function you want to perform, including any copy settings in the same command.
- The HP Accessibility Assistant repeats the request back to you and then asks you to confirm the request is correct.
- Wait for the ding sound, and then respond.
- The HP Accessibility Assistant says, “Preparing job†and then pulls the original document into the printer and completes the copy request.
- On the left side of the HP Accessibility Assistant, there are three additional functions.
- The two buttons control volume.
- Press the bottom button to decrease the volume, and press the top button to increase the volume.
- Keep in mind, adjusting the volume does not change the default settings.
- Default settings restore at the end of each user session.
- Above the volume buttons is a 3.5-millimeter headset jack.
- Plug a headset or headphones with a 3.5-millimeter input into the jack to allow for privacy of navigation and narration during use.
- For headphones without a microphone, continue speaking voice commands directly to the HP Accessibility Assistant.
- For headsets with a microphone, the HP Accessibility Assistant microphone is automatically disabled, and commands are received through the headset.
- For more information on using the HP Accessibility Assistant, refer to the HP Accessibility Assistant User Guide or go to hp.com/support/HPAA.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
HP Accessibility Assistant Button Functions | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, how to use the HP Accessibility Ass...HP Accessibility Assistant Button Functions | HP Printers | HP
Learn how to install the HP Accessibility Assistant on your HP LaserJet MFP in the HIP2, or Hardware Integration Pocket, or attach it to the printer using a USB cable.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to install the HP Accessibility Assistant:
- From the home screen of the printer control panel, navigate to Reports, and then navigate to view or print a Configuration Page to check the firmware version.
- Go to support.hp.com/drivers to download any available software or drivers for your HP printer.
- The HP Accessibility Assistant requires the printer language set to English, and all Voice Commands must be spoken in English.
- Unpack and remove all supplies from the box.
- A small, flat bladed screwdriver is required for installing the HP Accessibility Assistant in the HIP2 pocket, but does not come inside the box.
- Press the Power button to turn off the printer.
Follow these steps to install the HP Accessibility Assistant in the HIP2 Pocket.
- On the HIP2 cover, slide the flat tip of the screwdriver into the gap, and then lift the cover and remove it from the HIP2 pocket.
- From the unboxed materials, select the shorter of the two USB cables.
- On the back of the HP Accessibility Assistant, locate the connection port.
- Slide the six pin connector end of the USB cable into the port.
- Inside the HIP2 pocket, slide the other end of the cable into the USB port.
- Position the HP Accessibility Assistant so the buttons face up and the volume controls face away from the printer control panel, and then install it into the HIP2 pocket until it snaps into place.
- Press the Power button to turn on the printer.
- This completes installing the HP Accessibility Assistant in the HIP2 pocket.
Follow these steps to install the HP Accessibility Assistant using an external USB port on the printer.
- From the unboxed materials, select the longer of the two USB cables.
- On the back of the HP Accessibility Assistant, locate the connection port.
- Slide the six pin connector end of the USB cable into the port.
- From the unboxed materials, select the back cover plate and align the cable guide into the notch on the back.
- Press the back cover plate firmly until it snaps into place.
- From the unboxed materials, use the Velcro strips to attach the HP Accessibility Assistant to the printer.
- For each Velcro strip, peel off the backing and attach it to a rubber foot on the back cover plate.
- Peel off the remaining backing on the Velcro strips, and then press the HP Accessibility Assistant down firmly to attach it to the side or the top of the printer.
- On the printer, connect the other end of the cable into any available USB port.
- Press the Power button to turn on the printer.
- This completes installing the HP Accessibility Assistant to the printer through an external USB port.
- For more information on using the HP Accessibility Assistant, refer to the HP Accessibility Assistant User Guide or go to hp.com/support/HPAA.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
HP Accessibility Assistant Installation | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, how to install the HP Accessibility...HP Accessibility Assistant Installation | HP Printers | HP
This video has been updated: https://youtu.be/jKaSfT11VqE
Learn how to update your account information in HP Connected. For more information on updating your HP Connected account information, visit our support site https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to update your account information in HP Connected:
- On your computer or mobile device, go to hpconnected.com, and then select Sign In.
- Enter the email address and password for your HP Connected account, and then select Sign In.
- In the upper-right corner, select your account name, and then select Settings.
- Select Edit next to an account setting, and then update your information.
- Select Save Changes for each modified setting and your HP Connected account information is updated.
This video was produced by HP
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Update Your Account Information in HP Connected | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, HP Connected Account, update accoun...How To Update Your Account Information in HP Connected | HP Printers | HP
Learn how to load A4 paper in HP LaserJet Enterprise, OfficeJet Enterprise, and PageWide Enterprise printers. Properly loading paper minimizes paper feed issues and jams.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Steps to load paper in HP LaserJet Enterprise, OfficeJet Enterprise, and Pagewide Enterprise Printers:
- Slide out the paper guides.
- Remove a stack of paper from its packaging.
- Flex the stack of paper.
- Load the stack into the paper tray.
- Slide the paper guides inward so they rest against the stack.
- Slide in the paper tray.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Loading A4 Paper in HP LaserJet, OfficeJet, and Pagewide Printers | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, load paper, load A4 paper on printer, LaserJet Enterprise, OfficeJet Enterprise, PageWide Enterprise, HP, Hewlett Packard, troubleshooting, tutoria...Loading A4 Paper in HP LaserJet, OfficeJet, and Pagewide Printers | HP Printers | HP
Learn about the Output Platen Covers used in HP Latex 330, 360 and 370 Printers.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Know more about fabric component used in the output banner platen cover:
- when running a long fabric run, use the Take-up-Reel(TUR)
- HP Latex 360 and 370 Printer customers, order new Velcro metal banner output platen covers from our support team
- HP Latex 300 printer customers order them separately, not included with the printer.
- HP Latex 310 printer customers, need to manually adjust the dimensions of the fabric as the cover is designed for a 64-inch wide printer and not 54- inch wide printer.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Output Platen Covers: HP Latex 330, 360 and 370 Printers | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, printing to fabric on HP Latex printer, printing on fabric, latex textile printing, fabric for latex printer, Fabric and latex printers, Output Pla...Output Platen Covers: HP Latex 330, 360 and 370 Printers | HP Printers | HP
This video has been updated: https://youtu.be/qjyat145YtY
Learn how to remove a printer from your HP Connected account.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to remove a printer from your HP Connected account:
- On your computer or mobile device, go to hpconnected.com, and then select Sign In.
- Enter the email address and password for your HP Connected account, and then select Sign In.
- If multiple printers are linked to your HP Connected account, find the printer you want to update, and select Change Settings.
- Otherwise, your printer settings display automatically.
- Under the name of your printer, select Remove Printer.
- Confirm the printer shown is correct, and then select Remove to finalize removing the printer from your HP Connected Account.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Remove a Printer from Your HP Connected Account | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, how do i remove a printer from hp c...How To Remove a Printer from Your HP Connected Account | HP Printers | HP
This video has been updated : https://youtu.be/WH33qdl_aTY
Learn how to register your printer with HP connected. HP Connected is an online service that supports web-connected printing services, including ink delivery and sending print jobs directly from your smartphone. For more information on setting up an HP Connected Account, visit our support site https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to register your printer with HP connected:
- On your computer or mobile device, go to hpconnected.com.
- Select Create Account.
- Enter your information.
- Review the terms of use, and then select the check box to agree to the terms.
- Select Create Account.
- Verify your information, and then select Yes, it’s correct.
- Enter the claim code from the Printer Info page that printed when you enabled Web Services on your printer.
- The printer code is only valid for forty-eight hours from the time it prints.
- If it has been longer than forty-eight hours, print a new info page.
- If you do not know how to print a new info page, try the guided tour to assist you.
- With the claim code entered, select Add to start using web-connected printing services.
- Customize your HP ePrint email address to make it easier to remember.
- In the ePrint Address section, enter a custom email address, and then select Submit.
- Use the updated address when sending print jobs from a device to your printer via email.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Register Your Printer with HP Connected | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, how to register your printer with H...How To Register Your Printer with HP Connected | HP Printers | HP
This video has been updated: https://youtu.be/JiR4YsKCeLU
Learn how to add a new printer to your HP Connected account directly from your account page. For more information on setting up an HP Connected Account, visit our support site https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to add a new printer to your HP Connected account:
- On your computer or mobile device, go to hpconnected.com, and then select Sign In.
- Enter the email address and password for your HP Connected account, and then select Sign In.
- If you already have a printer added to your account and are adding another one, select Add Printer.
- Otherwise, the Add a Printer screen loads automatically.
- Enter the claim code from the Printer Info page that printed when you enabled Web Services on your printer.
- The printer code is only valid for forty-eight hours from the time it prints.
- If it has been longer than forty-eight hours, print a new Info page.
- If you do not know how to print a new Info page, try the guided tour to assist you.
- With the claim code entered, select Add to start using web-connected printing services.
- Customize your HP ePrint email to make it easier to remember.
- In the ePrint Address section, enter a custom email address, and then select Submit.
- Use the updated address when sending print jobs from a device to your printer via email.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Add a Printer to Your HP Connected Account | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, how do i add a printer from hp conn...How To Add a Printer to Your HP Connected Account | HP Printers | HP
This video has been updated: https://youtu.be/KQ5kSmgrS7Q
Learn how to change the ePrint email address from your HP Connected Account. For more information on changing your HP ePrint Email Address from your HP Connected Account, visit our support site https://support.hp.com/us-en/document...
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to change the ePrint email address from your HP Connected Account:
- On your computer or mobile device, go to hpconnected.com, and then select Sign In.
- Enter the email address and password for your HP Connected account, and then select Sign In.
- If multiple printers are linked to your HP Connected account, find the printer you want to update, and select Change Settings.
- Otherwise, your printer settings display automatically.
- In the ePrint Address section, enter a new email address for your printer, and then select Submit.
- If the email address entered is not available, the form reloads with the text box empty.
- Enter a different address, and then select Submit.
- With the new address accepted, a success message displays and you can resume sending ePrint jobs using the new printer email address.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Change Your Printer Email Address from HP Connected | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, change printer email address from H...How To Change Your Printer Email Address from HP Connected | HP Printers | HP
Learn how to get the printer code for HP printers without a touchscreen display. For more information on using the printer claim code to add your printer to the HP Connected service, visit our support site https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to get the printer code for HP printers without a touchscreen display:
- On the printer control panel, press the Wireless and Information buttons at the same time to print a Network Configuration page that contains your printer IP address.
- On a computer or device connected to the same network as the printer, open a web browser.
- Type the printer IP address, and then press Enter or select the Go icon or button.
- If a message displays indicating that accessing the website might not be safe, select the option to continue to the website.
- From the EWS, select the Web Services tab.
- Enable Web Services to print an information sheet containing your printer code.
- If Web Services is already enabled but you don’t have your printer code, disable and then re-enable Web Services to print a new information sheet.
- The printer code is valid for forty-eight hours from the time it prints.
- With the printer code, log in to your HP Connected account and add your printer.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Get the Printer Code for HP Printers Without a Touchscreen Display | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, printer claim code, hp connected, get, find, print, no display, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, h...How To Get the Printer Code for HP Printers Without a Touchscreen Display | HP Printers | HP
Learn more about the Connection Inspector which can assess potential security threats.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Connection Inspector detects a network attack using DNS Network Anomaly Detection algorithms developed by HP Labs and implemented by HP’s FutureSmart firmware team. The solution checks DNS connection requests to ensure that devices are not trying to connect to Malware Command and Control Centers on the Internet.
- When a Connection Inspector event, occurs the control panel removes access to available features.
- The device then displays the 33.05.31 Connection Inspector message briefly before rebooting.
- The error message screen will be displayed while automatically cancelling any current print jobs.
- If the Auto Recovery feature is enabled, the device will automatically reboot when a Connection Inspector event occurs.
- If this is the second event detected within 30 minutes, or the Auto Recovery feature is disabled, the device will reboot and hold in the device pre-boot menus.
- After a Connection Inspector event, the device performs a system restart.
- If configured so that syslog messages are sent to a Security Information Event Management system, SPLUNK in this case, will display the Connection Inspector event so that security personnel can take real-time appropriate action.
- Intrusion Detection, Whitelisting, HP SureStart, and other security occurrences also generate syslog events that are sent to SPLUNK.
- The SPLUNK status screen shows that a Connection Inspector Network Anomaly has been detected.
- Once a Connection Inspector event is received in SPLUNK, it can be configured to send an email to any email address.
- This enables an administrator to take appropriate action remotely.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Connection Inspector Demonstration | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, training, connection inspector, wha...Connection Inspector Demonstration | HP Printers | HP
Learn how to load Jumbo Substrate Rolls in the HP Latex 3800 Jumbo Roll Solution.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Follow these steps to load Jumbo Substrate Rolls in the HP Latex 3800 Jumbo Roll Solution:
- Turn on the printer, push the blue button next to the power switch to rearm the printer, and then move the rubber spindles, loading table, and curing module to their loading positions.
- On the jumbo input unit control panel, set the unwinder and rewinder speeds to zero, and then set the printer mode to Manual.
- Repeat these steps on the jumbo output unit control panel.
- Turn on and enable the jumbo input and output units.
- On the jumbo input unit control panel, touch Home to move the steering modules to the center of the printer.
- Align the red dots.
- Press the Release button, and then slide the handwheel out of the unit.
- If the red dots do not align, use the unwinder to align them.
- Press the Release button, and then slide the handwheel out of the unit.
- If the handwheel does not move, check for any obstructions or damage to the handwheel.
- Unlock and open the jumbo input and output operator platforms.
- On the jumbo input unit, slide the spindle into the core and center it.
- Use pressurized air to inflate the spindle bladders.
- Use an overhanging crane to lift the jumbo roll from the spindle and lower it into place.
- Repeat these steps on the jumbo output unit.
- From the IPS, or Internal Print Server, view the Recommended tension settings for the loaded substrate.
- Use the table to calculate counterweights based on tension and substrate width.
- Combine and load the two, three, and five kilogram weights to distribute weight evenly on both ends of each bar.
- Before threading substrate through the jumbo input unit, make sure the area beneath the tension bar is free from foreign objects.
- Set the unwinder spin direction according to your substrate roll winding direction.
- Set the unwinder speed to thirty percent, and then thread the substrate through the jumbo input unit.
- Guide the leading edge of the substrate through each part of the jumbo input unit as it unwinds.
- Set the unwinder to zero.
- Close the loading table while keeping the substrate under even tension.
- Push the rubber spindle into the working position and close the latches.
- Close the operator platform.
- Set the unwinder spin direction according to your substrate roll winding direction.
- Set the unwinder mode to Automatic.
- Move the steering sensor to the nearest substrate edge and center it within the sensor field of view, and then tighten the screw to secure it.
- Only LED4 should be lit.
- Set the input steering to Automatic.
- Make sure the substrate is free of any damaged or baggy regions.
- From the IPS, use the arrow buttons to continue feeding substrate through the printer, under the printer output rubber spindle.
- Push the printer output rubber spindle into its working position, and then secure the latches.
- Close the curing module and its latches, and then close the front door.
- If your setup does not include a jumbo output unit, complete the loading process by going to the IPS and touching Finish.
- If your setup includes a jumbo output unit, continue the loading process by going to the IPS and using the arrow buttons to advance six hundred centimeters of substrate.
- Stop feeding the substrate when it reaches the output core.
- Attach the substrate to the core, keeping the tension as even as possible.
- Close the jumbo output unit operator platform.
- Set the rewinder spin direction according to the output roll winding direction.
- Set the rewinder mode to Automatic.
- The tension bar moves up along its track to reach a stable position.
- If necessary, adjust the position of the steering sensor by loosening the screw holding the sensor in place.
- Move the steering sensor to the nearest substrate edge and center it within the sensor field of view, and then tighten the screw to secure it.
- Only LED4 should be lit.
- Set the output steering mode to Automatic.
- Make sure the substrate is free of any damaged or baggy regions.
- From the IPS, touch Finish.
- The printer finalizes the loading process.
- With the process complete, you can send jobs to print on the jumbo substrate roll.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Load Jumbo Substrate Rolls in the HP Latex 3800 Jumbo Roll Solution | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, How To Load Jumbo Substrate Rolls, ...How To Load Jumbo Substrate Rolls in the HP Latex 3800 Jumbo Roll Solution | HP Latex | HP
Learn how to fix your HP printer when it does not turn on. For more information, visit our support site https://support.hp.com/us-en/document....
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to fix your HP printer when it does not turn on:
- Reset the power module, and then reconnect the printer power cord to a working wall outlet.
- Disconnect the power cord from the printer.
- Unplug the other end of the power cord from its power source.
- If your printer has an external power supply, also disconnect the power cord from the block.
- Wait 30 seconds, and then reconnect the power cord to the block.
- Reconnect the other end of the power cord to the rear of the printer, and then plug the power cord directly into a working wall outlet.
- A power strip or surge protector might not provide enough power for your printer.
- Press the Power button.
- If the printer does not turn on, check the power supply compatibility.
- Your printer requires a specific amount of power to work properly.
- To avoid power issues, use the power module and cord that came with your printer.
- For printers that use an external power module, the power supply must match the voltage and amperage specifications of your printer.
- Locate this information printed on the power module, and then check the specifications listed on the back of the printer.
- Compare the power cord connector to the color and shape of the input port on the printer.
- If they do not match, find the correct power cord and power module.
- Reconnect the power cord into the printer without forcing it.
- Press the Power button.
- If the printer still does not turn on, go to the next step.
- If your power module is not working, a replacement might be available at the HP Parts Store.
- Go to parts.hp.com and type the part, product, or serial number found on the power module.
- If a replacement is not available, continue to the next step.
- If the issue continues, service the printer.
- Contact HP for service and warranty options.
#HP #HPSupport #HPPrinters
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Fix Your HP Printer When It Does Not Turn On | HP Printers | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshoot, tutorial, diy, electronics, printer, how to, howto, error message, support, help, fix, power, test, turn on, res...How To Fix Your HP Printer When It Does Not Turn On | HP Printers | HP
Learn how to replace the printhead cleaning roll station transmission box on the HP Latex R Printer series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace the printhead cleaning roll station transmission box on the HP Latex R Printer series:
- Before replacement, make sure the printer is idle.
- Unload all substrate, and close all covers and windows.
- From the IPS, or Internal Print Server, touch Maintenance.
- From the IPS, touch Replace a printhead cleaning roll station transmission box, and then touch Start.
- The screen displays instructions for the replacement process.
- Go to the input side of the printer.
- Use a screwdriver to remove the rear service cover.
- On the motor to replace, disconnect the encoder and control cables.
- Use a screwdriver to loosen the three T-25 screws securing the motor.
- Remove the motor transmission box from the printer.
- Do not touch the gear connecting the motor and the printer.
- Install the new motor in the printer, and then tighten the three T-25 screws to secure it.
- Connect the encoder and control cables to the motor.
- Reinstall the rear service cover.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
HP Latex R Printer: Replacing the Printhead Cleaning Roll Station Transmission Box | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, Replace the Printhead Cleaning Roll...HP Latex R Printer: Replacing the Printhead Cleaning Roll Station Transmission Box | HP Latex | HP
Learn how to replace the printhead cleaning roll station pinchwheel on the HP Latex R Printer Series
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace the printhead cleaning roll station pinchwheel on the HP Latex R Printer Series:
- Before replacement, make sure the printer is idle, unload all substrate, and close all covers and windows.
- From the IPS, or Internal Print Server, touch Maintenance.
- In the list of maintenance operations, touch Replace the printhead cleaning roll station pinchwheel, and then touch Start.
- The screen displays instructions for the replacement process.
- Open the carriage cover and printhead cleaning roll door.
- Pull the black knob to the side to release the pinch system.
- Use pliers or an eight-millimeter wrench to loosen the screw, and then remove the old pinchwheel.
- To install the new pinchwheel, insert the pin, and then tighten the screw to secure it.
- Use the black plastic knob to close the pinchwheel.
- Close the printhead cleaning roll door and the carriage cover.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
Replacing the Printhead Cleaning Roll Station Pinchwheel on the HP Latex R Printer | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, Replace the Printhead Cleaning Roll...Replacing the Printhead Cleaning Roll Station Pinchwheel on the HP Latex R Printer | HP Latex | HP
Learn how to replace an alignment bar on the HP Latex R Printer Series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace an alignment bar on the HP Latex R Printer Series:
- Before replacement, make sure the printer is idle.
- Unload all substrate and close all covers and windows.
- From the IPS, or Internal Print Server, touch Maintenance.
- In the list of maintenance operations, touch Replace an alignment bar, and then touch Start.
- The screen displays instructions for the replacement process.
- Move the front alignment bar to the service position.
- Go to the input side of the printer and use a screwdriver to loosen the screws and remove the front alignment bar.
- Place the alignment bar on a flat surface.
- Position the new alignment bar at the pins, and then tighten the screws to secure it.
- From the IPS, calibrate the alignment bar.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Replace an Alignment Bar on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, Replace an Alignment Bar on the HP ...How To Replace an Alignment Bar on the HP Latex R Printer Series | HP Latex | HP
Learn how to replace the carriage condensate ventilator on the HP Latex R Printer Series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace the carriage condensate ventilator on the HP Latex R Printer Series:
- Before replacement, make sure the printer is idle.
- Unload all substrate and close all covers and windows.
- From the IPS, or Internal Print Server, touch Maintenances.
- From the list of maintenance operations, touch the check box next to Replace the carriage condensate ventilator, and then touch Start.
- The screen displays instructions for the replacement process.
- Keep in mind, if you follow the steps in this video, the instructions can just be used as reference.
- Open the carriage cover.
- Use a T-20 screwdriver to loosen the five top screws and then the four lateral screws attaching the condensate ventilator to the carriage.
- Move the carriage to the left to reach the third and fourth screws.
- Open the top window and the curing module.
- Move the carriage to the left, and then tilt the condensate ventilator to remove it from the carriage.
- Install the bottom of the condensate ventilator, and then install the top.
- Move the carriage to the right.
- Tighten the four lateral screws and then the five top screws to secure the condensate ventilator to the carriage.
- Close the curing module and then the top window.
- Close the carriage cover.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Replace the Carriage Condensate Ventilator on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, Replace the Carriage Condensate Ven...How To Replace the Carriage Condensate Ventilator on the HP Latex R Printer Series | HP Latex | HP
Learn how to replace the Printhead Cleaning Roll Kit Components on the HP Latex R Printer Series.
Follow these steps to replace the Printhead Cleaning Roll Kit Components on the HP Latex R Printer Series:
- The printhead cleaning roll kit contains a new cleaning roll, printhead cleaning blade, aerosol filters, a left spittoon foam, a drop-detector spittoon foam, Distilled water
- From Internal Print Server, touch the Applications bar, then Other supplies and then touch Replace.
- Follow these steps to replace the left spittoon foam.
- Open the top cover, and then pull the curing module out of the printer.
- From the left side of the printer, remove the left spittoon foam.
- Bend the foam and slide it into the left spittoon slot, making sure it lays flat.
- From the IPS, touch Next to move to the next task.
- Follow these steps to replace the left printhead cleaning blade.
- Next to the left spittoon, grab the center of the left printhead cleaning blade, and then pull it out of the printer.
- Install the new left printhead cleaning blade into the printer.
- Close the curing module, and then close the top cover.
- From the IPS, follow these steps to refill the water tank.
- Open the water tank cap and slowly fill the tank with distilled water
- Touch Next to follow these steps to replace the aerosol filters.
- Open the carriage cover, pull up on the latch on the right side of the aerosol filter module.
- Open the filter lid, remove the frame and the filter from the frame.
- Use a screwdriver and then maintenance kit brush to clean the frame.
- Install the new filter into the frame, and then slide the frame into the aerosol container, close the filter lid, and then close the latch.
- Repeat this process for the other aerosol filter.
- With both filters replaced, close the carriage cover.
- Follow these steps to empty the printhead cleaning waste bottle.
- Open the printhead cleaning roll door.
- Remove the waste bottle from the printer, and then empty it.
- Place the empty waste bottle back in its original location.
- Follow these steps to replace the drop-detector spittoon foam.
- Open the carriage cover. manually move the carriage to the left.
- Slide the drop-detector spittoon foam out of the printer.
- Slide the new drop-detector foam into the its slot, making sure it lays flat.
- Follow these steps to replace the printhead cleaning roll.
- With the carriage cover still open, open the printhead cleaning roll door.
- From the IPS, touch Next to wind the printhead cleaning roll material.
- Pull the upper-left black knob, and then move the pinch system aside.
- Remove the end of the roll and use it to thoroughly clean and remove all ink waste from the printer.
- Use the end of the roll to clean the orange printhead cleaning blade,
- the transparent printhead cleaning blade,
- the entire surface of the middle diverter,
- the left diverter, and the left latch.
- Wipe any ink and fiber particles from each piece after cleaning.
- Use a putty knife and screwdriver to scrape the dried ink from sloping surfaces and to remove waste from the drilling hole respectively.
- Clean the fluid dispenser nozzle to make sure it’s not clogged.
- Turn the feed roller until you reach the end of the roll.
- Turn the take-up roller until the material is completely out of the assembly.
- Slide both rolls off their axles.
- Follow the instructions provided with the new roll and dispose of the roll with the used cleaning material.
- Remove the empty core and keep it to use as a take-up core.
- Slide the take-up core onto the lower axle.
- Slide the end cap on to the roll until it clicks into place.
- The empty core must be aligned against the end cap.
- Slide the new roll onto the upper axle.
- Slide the end cap on the upper axle, and then slide the cap and axle together.
- You will hear a click when correctly installed.
- Slide the leading edge of the roll over the upper rollers, but below the central diverter.
- Thread the leading edge of the cleaning material through the rollers on the left.
- Do not thread the leading edge behind the roller on the left. This roller must stay between the roll and the material.
- Thread the leading edge down the left side of the assembly.
- Install the leading-edge tabs into the slots in the take-up core.
- Turn the take-up core several times to attach the roll to the core.
- Move the black knob to the original position to restore the pinch system.
- Close the printhead cleaning roll door, and then close the carriage cover.
- From the IPS, touch Close,a progress bar indicates the stages of completion of all replacement tasks.
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Replacing the Printhead Cleaning Roll Kit Components on the HP Latex R Printer | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, simple tutorial, Replace the Printh...Replacing the Printhead Cleaning Roll Kit Components on the HP Latex R Printer | HP Latex | HP
Learn how to replace the Spectrophotometer Shutter on the HP Latex R Printer Series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace the Spectrophotometer Shutter on the HP Latex R Printer Series:
- From the IPS, or Internal Print Server, touch Maintenance.
- From the IPS, touch Replace the Spectrophotometer Shutter, and then touch Start.
- The screen displays instructions for the replacement process.
- Turn off the printer and main switch.
- On the right side of the printer, use a screwdriver to loosen the two screws securing the ink delivery system cover.
- Remove the rear ink delivery system cover.
- Unplug the spectrophotometer power cable.
- With a screwdriver, loosen the screw securing the spectrophotometer shutter.
- Remove the spectrophotometer shutter.
- Install the new spectrophotometer shutter.
- Plug the spectrophotometer power cord back into the printer.
- Tighten the screws to secure the rear ink delivery system cover.
- Make sure all doors and covers on the printer are closed.
- Turn on the printer and the main switch.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Replace the Spectrophotometer Shutter on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, simple tutorial, replace, Spectroph...How To Replace the Spectrophotometer Shutter on the HP Latex R Printer Series | HP Latex | HP
Learn how to replace a Carriage Fan on the HP Latex R Printer Series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace a Carriage Fan on the HP Latex R Printer Series:
- From the IPS, touch Maintenance.
- From the IPS, touch Replace the carriage fan, and then touch Start.
- The screen displays instructions for the replacement process.
- Turn off the printer and main switch.
- Open the carriage cover.
- Manually move the carriage to the left.
- On the carriage electrical cover, use a screwdriver to loosen the nine screws.
- Separate the cables from the electrical cover, and then remove it.
- On the carriage main PCA, unplug the fan cable from the J49 connector.
- Use a screwdriver to loosen the four screws and detach the fan from the carriage.
- Install the new fan, and then tighten the four screws to secure it.
- Plug the fan cable into the J49 connector on the carriage main PCA.
- Reinstall the electrical cover, making sure not to clamp the cables.
- Tighten the nine screws on the electrical cover.
- Close the carriage cover.
- Make sure all doors and covers on the printer are closed.
- Turn on the printer and the main switch.
This video was produced by HP
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Replace a Carriage Fan on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, replace, Carriage Fan, HP Latex R P...How To Replace a Carriage Fan on the HP Latex R Printer Series | HP Latex | HP
Learn How to replace the Crash Sensor Legs on the HP Latex R Printer Series..
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace the Crash Sensor Legs on the HP Latex R Printer Series:
- From the IPS, or Internal Print Server, touch Maintenance.
- From the IPS, touch Replace Crash Sensor Leg, and then touch Start.
- The screen displays instructions for the replacement process.
- Turn off the printer and the main switch.
- Open the carriage cover.
- Slide the carriage to the right until it stops.
- On the front crash sensor leg, use a screwdriver to loosen the two screws securing the silver bracket, and then remove it.
- Loosen the screw that holds the yellow cover, and then remove it.
- Slide the carriage to the left.
- Making sure not to touch the printhead cleaning roll, turn the crash sensor leg forty-five degrees to the left, and then remove it.
- Align the new leg at a forty-five-degree angle, and then install it.
- Reinstall the silver bracket and tighten the screws to secure it.
- Reinstall the yellow cover and tighten the screw to secure it.
- Slide the carriage to the right until it stops.
- To replace the rear crash sensor leg, loosen the screw that holds the yellow cover, and then remove it.
- Turn the leg counterclockwise and remove it.
- Install the new leg horizontally.
- When correctly in place, turn it clockwise to tighten it.
- Reinstall the yellow cover and tighten the screw to secure it.
- Turn on the printer and main switch.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Replace the Crash Sensor Legs on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, replace, Clean or Replace Printhead...How To Replace the Crash Sensor Legs on the HP Latex R Printer Series | HP Latex | HP
Learn how to replace a Curing Fan Resistor Module on the HP Latex R Printer Series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to replace a Curing Fan Resistor Module on the HP Latex R Printer Series:
- From the IPS, or Internal Print Server, touch Maintenance.
- In the list of maintenance operations, touch Replace a curing fan resistor module, and then touch Start.
- The screen displays instructions for the replacement process.
- Turn off the printer and the main switch.
- Move the output roller down.
- Use a screwdriver to completely loosen the three screws on the curing module cover.
- Lift the curing module cover.
- Separate the temperature sensor cable, and then disconnect the two remaining power cables from the connection panel.
- Unroute the cables from their path.
- Use a screwdriver to loosen the screw securing the curing fan resistor module to the curing module.
- Slide the assembly out of the printer.
- Use the pins to position the new curing fan resistor module, and then push it in.
- Tighten the screw to secure the curing fan resistor module to the curing module.
- Reroute and reconnect the power cables.
- Push the cover of the curing module to close it, and then tighten the three screws to secure it.
- Raise the output roller.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Replace a Curing Fan Resistor Module on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, replace, Clean or Replace Printhead...How To Replace a Curing Fan Resistor Module on the HP Latex R Printer Series | HP Latex | HP
Learn how to perform Monthly Maintenance on the HP Latex R Printer Series.
For other helpful videos go to http://hp.com/supportvideos or http://youtube.com/hpprintersupport.
More support options for your printer are available at http://hp.com/support.
Continue the Conversation:
http://hp.care/SupportForums
http://hp.care/FacebookSupport
http://hp.care/TwitterSupport
Follow these steps to perform Monthly Maintenance on the HP Latex R Printer Series:
- From the IPS, or Internal Print Server, touch Maintenance.
- Select Clean the drop-detector rods, Clean the substrate-advance belt, and Clean the bottom of the carriage, the line sensor and the crash sensor.
- Then touch Start to view instructions for the maintenance process.
- Follow these steps to clean the drop detector rods.
- Open the carriage cover.
- Manually move the carriage to the left.
- Dampen a lint-free cloth with distilled water.
- Clean the drop detector rods with the cloth until all ink is cleaned.
- Close the carriage cover.
- Follow these steps to clean the substrate-advance belt.
- Lower the alignment bar.
- Remove the standard extension tables.
- Pour a latex solvent liquid over the dried ink.
- Use a brush to remove the ink from the belt.
- Use a lint-free cloth to finish cleaning the zone.
- Move the belt backward and forward to clean all through the belt, repeating the process when needed.
- Follow these steps to clean the bottom of the carriage, the line sensor, and the crash sensor.
- Use the IPS to move the carriage beam to its highest position.
- Move the carriage to the left until it reaches the ink delivery system side of the printer.
- Turn off the printer and the main switch.
- Remove the rear ink delivery system cover to access the bottom of the carriage.
- Clean the sides of the printheads with a lint-free cotton swab dampened with distilled water.
- Use another cotton swab to clean the optimizer printhead.
- Clean the bottom of the carriage with a lint-free cloth dampened with distilled water.
- Do not touch the printheads.
- Wipe the line sensor with another cotton swab dampened with isopropyl alcohol.
- Wait three or four minutes for the alcohol to evaporate completely.
- Manually move the carriage to the left until both crash sensors are reachable.
- Use a lint-free cloth dampened with distilled water to clean the sensors.
- Wait three or four minutes for the water to evaporate completely.
- Reinstall the rear ink delivery system cover.
- Close all doors and covers.
- Turn on the printer and main switch.
- The carriage automatically returns to the service station.
#HP #HPSupport #HPLatex
SUBSCRIBE: http://bit.ly/PrinterSupport
SHOP NOW: http://store.hp.com/us/en/
About HP:
HP Inc. creates technology that makes life better for everyone everywhere — every person, every organization, and every community around the globe. Through our portfolio of printers, PCs, mobile devices, solutions, and services, we engineer experiences that amaze.
Connect with HP:
Visit HP WEBSITE: http://www.hp.com
Like HP on FACEBOOK: https://www.facebook.com/HP
Follow HP on TWITTER: https://twitter.com/HP
Follow HP on INSTAGRAM: https://www.instagram.com/hp
Follow HP on LINKEDIN: https://www.linkedin.com/company/hp
This video was produced by HP.
How To Perform Monthly Maintenance on the HP Latex R Printer Series | HP Latex | HP
https://www.youtube.com/user/HP
Palavras-chave desta postagem
yt:cc=on, HP, Hewlett Packard, troubleshooting, tutorial, howto, diy, electronics, printer, how to, support, help, learn, replace, Clean or Replace Printhead...How To Perform Monthly Maintenance on the HP Latex R Printer Series | HP Latex | HP
